Team-BHP - A green Ninja 250R it definitely is!

And I was wondering there was some more stuff I missed mentioning which was in the backpack :eek:.

I also carried 5 boxes of 4 sachets each of Bodyfuelz fast charge sports drink. Worked better for me than gatorade. The Red Bulls were not for hydrating on the go anyways and kept it for other activities at the place we were visiting.

Quote:

Originally Posted by ebonho (Post 2814076)

My favorite perk up drink on refreshment butt breaks while riding is a chilled Thums Up, one fresh lime squeezed in, some salt, and some chaat masala.

My favorite too clap:

Quote:

Originally Posted by Shubz (Post 2814064)

I picked up a water pouch from Wildcraft which can hold 2 ltrs of liquid, with a pipe. Cost: Rs.499.

I bought this hydration pack early this year and used it a couple of times during my ride to Kodai and other places. Works like a charm and for the price its a great VFM product. I did not want to spend 3k+ on camelback products since the usage is pretty limited.

I place the hydration pack in the laptop compartment of my backpack and the velcro strap goes through the filler cap so the pack itself stays in place without moving around.

Quote:

Originally Posted by Shubz (Post 2814064)

I picked up a water pouch from Wildcraft which can hold 2 ltrs of liquid, with a pipe. Cost: Rs.499. The pouch can be conveniently tucked away in the back pack and there is a tube which comes over the shoulder and can be used to sip water without having to take off the helmet. You may ask - would water leak -- the answer is No. It comes with a rubber cap and even after taking off the cap, one need to twist the nozzle for water/liquid to flow out.

PS: This pouch cannot be filled with aerated drinks/milk etc - the smell would remain forever in it/the other liquids could possibly damage the pouch material as well.

Can you post a link or a photo of this please. How easy is the nozzle to sip from (twist?) while on the move?

Quote:

Originally Posted by Shubz (Post 2815000)

Will post by tonight. Definitely not recommended to SIP on the move. It takes 2 hands to remove the rubber top and then twist the sipper open.

I saw a friend using another similar pouch in bag setup where the nozzle had to be pressed against the front of the teeth to release the water. Not very convenient either.

The CamelBak's bite valve is really easy to use. Only problem is getting the pipe under the rim of the helmet and into your mouth on the move in a conventional shaped full face helmet (AGV type). If you have one of the newer designs where the mouth shield is pointed/peaked (like the motocross style hemmets), the pipe slips under and in much easier.

Quote:

Originally Posted by Shubz (Post 2815000)

It takes 2 hands to remove the rubber top and then twist the sipper open.

Quote:

Originally Posted by ebonho (Post 2815019)

I saw a friend using another similar pouch in bag setup where the nozzle had to be pressed against the front of the teeth to release the water.

The rubber cap on the tube for the Wildcraft product can be used in a similar way. Just poke some holes in it and suck when thirsty. I've not made any holes in the rubber cap though.

P.S. Sounds graphic but couldn't word this any differently. lol:

Quote:

Originally Posted by ebonho (Post 2815019)

Only problem is getting the pipe under the rim of the helmet and into your mouth on the move in a conventional shaped full face helmet (AGV type).

Yeah, i've faced this problem so I pull over when i'm thirsty. Gives me a few mins to get the blood flowing in my butt too.

Came back from a great trip to Hampi. Another friend of mine and I started on Saturday the 23rd June towards Badami to see the temples and the caves there. Must say amazing sculptures in the caves. Simply amazing! Next day, the Sunday we started towards Hampi. Spent the next 2 days there seeing all the temples and other ruins of the Viajayanagar kingdom and I was blown away looking at the amazing architecture and the carvings. We indeed have a super rich history!

For the luggage I had the Rynox tank and tail bag. Both held well throughout the entire ride. Tank bag could be more snugly fit. At one time, while taking a U-turn the bag hit the engine switch on the right handle and I almost fell :eek: .Immediately re-positioned the bag and this time lil away from the handle and it stayed put all throughout the journey. Magnets work great to hold the bag in place (although the bag on top slightly moves to sides, not a major botheration, hence mentioned it could be more snugly fit). The tail bag came with suction caps and they do not stay well on the tank (if used as a tank bag). The suction caps come off easily if the bag in heavy.

Meanwhile, while heading from Badami to Hampi, the FI light began to glow. :Shockked: Called Arif and he said nothing to worry as long as the bike is starting and doesn't behave weird while running. Fortunately for me, the bike was behaving just normal and did not give any trouble throughout the journey. Have to take the time tomorrow to the workshop to fix the FI warning.

Took the bike today to fix the FI warning. It turned out to be radiator fan relay malfunction and the fuse blew in order to prevent further problems. Fuse was replaced within 5 minutes and its all normal.

Our fellow T-BHPian Isodope had posted in his thread about how to check the FI Light warning. Its easy and I did it myself in the workshop today clap:

Here are the steps which he had posted:

1. Remove the pillion seat.
2. Look on the right side of the subframe - you'll find a lone wire that seems to have been forgotten because it's connected only at one end.
3. Turn your ignition key to the 'on' position and wait until everything settles.
4. Push the plastic sheath on the free end of the wire you just found back and ground the metal end on the chassis.
5. Watch the FI light - if it stays constantly on, you haven't grounded the wire properly. Try again, either with a firmer hand or on a different part of the chassis.
6. Once you get it right, the FI light will go off momentarily and then start flashing. There are long flashes and short flashes, separated by a second of the FI light staying off. Make sure you've got the entire sequence before you remove the wire from its grounding. Do this at least two times so that you've got the number of flashes right.
7. Look up the error codes from the list below and take appropriate action.

• 1 long/ 1 short: Main throttle sensor malfunction/wiring open or short
• 1 long/2 short: Inlet air pressure sensor malfunction, wiring open or short
• 1 long/ 3 short: Inlet air temperature sensor malfunction, wiring open or short
• 1 long/ 4 short: Water temperature sensor malfunction, wiring open or short
• 2 long / 1 short: Crankshaft sensor malfunction, wiring open or short
• 2 long/ 4 short alternated with 2 long/ 5 short: Speed sensor malfunction, wiring open or short
• 3 long/ 1 short: Vehicle down sensor malfunction, wiring open or short
• 3 long / 2 short: Sub throttle sensor malfunction, wiring open or short
• 3 long/ 3 short: Oxygen sensor malfunction, wiring open or short
• 5 long / 1 short: Stick coil #1 malfunction, wiring open or short
• 5 long/ 2 short: Stick coil #2 malfunction, wiring open or short
• 5 long/ 6 short: Radiator fan relay malfunction, wiring open or short
• 6 long/ 2 short: Sub throttle valve actuator malfunction, wiring open or short
• 6 long/ 4 short: Air switching valve malfunction, wiring open or short
• 6 long/ 7 short: Oxygen sensor heater malfunction, wiring open or short
• 9 long/ 4 short: Oxygen sensor malfunction, wiring open or short

Next planning on a trip to Mahabalipuram. Let's see if it works out.

Nice pics. Looks like you're having a ball with the bike.:thumbs up

It's been quite a long time since my last trip (2 months precisely) and I'm desperate for one (hopefully soon).

Since you're using bungee cords to secure your tailbag in place, use paint protection films on the contact areas to protect the painted parts from scratches. 3M has launched its PPF material for bikes and although a bit on the higher side in terms of cost it's totally worth it. No air bubbles whatsoever or any sticky adhesives to be worried about :)

Quote:

Originally Posted by n_aditya (Post 2826402)

Since you're using bungee cords to secure your tailbag in place, use paint protection films on the contact areas to protect the painted parts from scratches. 3M has launched its PPF material for bikes and although a bit on the higher side in terms of cost it's totally worth it. No air bubbles whatsoever or any sticky adhesives to be worried about :)

You said it Adi, having a great time! I tried looking for the 3M PPF but couldn't find in Hyderabad. Still hunting. Meanwhile to protect the contact areas, I used a soft cloth, covering the tail piece before placing the tail bag and tying with bungee cords. Worked great clap:

Just came back from 6 days of trip (15th to 20th Aug), exploring different terrains of Andhra (1800+ kms). Covered forests, coffee plantations, hills, temples, caves ghats, a mangrove forest, sea and coastal Andhra. Here are the details of route taken.

Day 1- Hyderabad--Warangal--Eturnagaram--Manuguru--Badrachalam

Day 2- Badrachalam-- Sileru-- Chintapalle-- Paderu--Araku

Day 3- Araku site seeing

Day 4- Araku -- Vizag--Tuni --Rajahmundry

Day 5- Rajahmundry--Kakinada-- Coringa Wildlife Sanctuary/Mangrove forest

Day 6- Rajahmundry--Vijaywada-- Hyderabad

This trip will be a real memorable one. Enjoy the pics :)