Team-BHP - My MM540XD upgrade

Quote:

Originally Posted by ex670c (Post 1833490)

Hi Nookala.Vinod,

That day will come when my MM540XD has
1) XD3P-2A FIP
2) RCBT PS
3) Front Locker
4) New Tyres
5) MM550XD Tail Gate
6) MM550XD windscreen assy. (Natural HVAC)

Regards,

Arka

Ofcourse, VN, you forgot to add one important point that cant be listed here. You and I are already in it on all fours!!!:uncontrol and Arka is ...

Arka ,please let me know if i am right :)

1) XD3P-2A FIP - Bolero or scorpio Engine?
2) RCBT PS - Power steering ok, but what is RCBT?
3) Front Locker - will this make both R&L wheels go in the same speed?
4) New Tyres - understood will cost 15-20k
5) MM550XD Tail Gate - what big difference is it going to make ?
6) MM550XD windscreen assy. (Natural HVAC) - I dont know if it is difficult to get it but you can always get it from pudhupet

All the best for the upgrades, and that day your Jeep will ROCK ! Palar

Quote:

Originally Posted by ex670c (Post 1833490)

Hi Nookala.Vinod,

That day will come when my MM540XD has
1) XD3P-2A FIP
2) RCBT PS
3) Front Locker
4) New Tyres
5) MM550XD Tail Gate
6) MM550XD windscreen assy. (Natural HVAC)

Regards,

Arka

Quote:

Originally Posted by ex670c (Post 1833490)

Hi Nookala.Vinod,

That day will come when my MM540XD has
1) XD3P-2A FIP
2) RCBT PS
3) Front Locker
4) New Tyres
5) MM550XD Tail Gate
6) MM550XD windscreen assy. (Natural HVAC)

Regards,

Arka

This would ensure that a two coat paint is a year away!!:DErrr....not a year away, may be years away, i forgot Portal axle upgrade on your jeeplol:

Quote:

Originally Posted by joshguy (Post 1833810)

Arka ,please let me know if i am right :)

2) RCBT PS - Power steering ok, but what is RCBT?

Re-circulating ball type (power steering)

-Biju

Quote:

Originally Posted by vinod_nookala (Post 1833893)

This would ensure that a two coat paint is a year away!!Errr....not a year away, may be years away, i forgot Portal axle upgrade on your jeep

Quote:

Originally Posted by matchless (Post 1833901)

Hi Arka,

Which winch are u planing to install ?

@ Nookala.Vinod PORTAL AXLEs on the NGCS MM550XD

@ Matchless - the same old Chinese One maybe a dual Motor Setup:D

Quote:

Originally Posted by ex670c (Post 1834347)

@ Nookala.Vinod PORTAL AXLEs on the NGCS MM550XD

@ Matchless - the same old Chinese One maybe a dual Motor Setup:D

Arka ,

you are yet to answer me. Points 1 and 3

Quote:

Originally Posted by joshguy (Post 1833810)

Quote:

Originally Posted by joshguy (Post 1835979)

Arka ,

you are yet to answer me. Points 1 and 3

Hi Joshguy,

Point#1 what have I written?

Point#3 What is a Locker?

Regards,

Arka

Quote:

Originally Posted by ex670c (Post 1831261)

Hi Guys,

The following work was done

1) Engine
i) Changed Vale Stem Seal.
ii) FIP Hub gear/pinion. Was the cause of erratic firing and and delayed starts, after this change the strating is crisp, engine feels revitailsed.
iii) Chain Tensioner. (Timing Case)
iv) Main Bearing Oil Seal (Crankshaft).
v) Oil-Cooler Assy.

Can you elaborate on the Oil- Cooler Assy work?

I thought the XD did not come with the Oil cooler?

Quote:

Originally Posted by fiery enzyme (Post 1837253)

Can you elaborate on the Oil- Cooler Assy work?

I thought the XD did not come with the Oil cooler?

Hi Bala,

The MM550XDs were fitted with an Oil Cooler Assembly. The same was carried over to the XD3P Bolero's in 2006 and even there on the SZ2600 and NEF2.49 TCIC.

You can seen the Oil Cooler on imported Peugeot Diesels (XD2S)

This assembly fits on the Oil Filter bracket and the Oil Filter Sits on top of this.

A direct Water Line inlet is connect from the Engine Head and the Oil Cooler Water Line Out is connected to the Water Pump.

How this works.
1) Oil from the Engine Block goes up to the Filter,
2) After Filtering, it Circulates in the Oil-Cooler
3) In the Oil-Cooler it circulates around coils which has a water jacket.
4) The Heat from the oil is absorbed by the Radiator Water/Coolant.

Regards,

Arka

PS - Spike can correct me if I'm wrong.

Quote:

Originally Posted by ex670c (Post 1839248)

Did the 540XDs have an oil cooler.

Quote:

Originally Posted by fiery enzyme (Post 1840764)

Did the 540XDs have an oil cooler.

Its seems like mine didn't.

SAAAAAR!!!!!!:eek:, If the MM540XD had an Oil Cooler why would I fit one which was fitted on Army MM550XD and Civilian Bolero's?

Regards,

Arka

Quote:

Originally Posted by ex670c (Post 1839248)

How this works.
1) Oil from the Engine Block goes up to the Filter,
2) After Filtering, it Circulates in the Oil-Cooler
3) In the Oil-Cooler it circulates around coils which has a water jacket.
4) The Heat from the oil is absorbed by the Radiator Water/Coolant.

Regards,

Arka

PS - Spike can correct me if I'm wrong.

Arka, i think there is a slight correction to this. The oil delivered to the oil cooler after getting cooled comes on to the other side of the element. The filtered oil then goes through the centre of the oil filter and is connected to the main oil gallery. Bypass valves are usually incorporated into this circuit.

Spike